WOCA Worktop Oil – oil for work surfaces and furniture

Oil is designed to impregnate untreated or pre-oiled wood surfaces indoors, such as kitchen worktops, window sills, tables, etc.

 

Consumption

Approx. 12-15 m²/L

Package

0.75l white or colorless – EUR 31.94

 

* The terms of the contract and the right of withdrawal can be found in the Documents section.

 

* This product is one of the regulations of the Cabinet of Ministers No. 255, 22nd article exceptions, where the customer cannot exercise the right of withdrawal.

31,94

Clear

Air-hardening oil that penetrates deep into the wood, leaving a tough water- and stain-resistant surface. The oil highlights the wood’s natural glow and gives the surface a natural, fresh appearance. Worktop Oil can be used on surfaces that are untreated or that have previously been oil-treated/sanded.

  • Provides a dirt and water-resistant surface
  • Natural appearance
  • Can be used on all wood varieties
  • Highlights the glow and grain structure of the wood
  • Safe for food contact

 

Colors: natural, white, grey and black

Density: 0.90-0.95 g/ml

Application area: for the care and maintenance of untreated or previously oil-treated/sanded surfaces. Only for indoor use.

Surface preparation: it is important that both wood and oil have a temperature of min. 15°C (preferably around 20°C) and air humidity of approx. 50 %. Make sure that the room is well-ventilated for optimal evaporation and drying time. Sand old and previously treated surfaces with grit 180 sandpaper. Vacuum clean the surface thoroughly. Thoroughly clean the surface with Intensive Wood Cleaner, mixed 1 part cleaner to 20 parts water. Then wash with clean water. After cleaning, leave the surface to dry for at least 8 hours at 20°C. Mix the oil thoroughly. Always remember to test on a less visible spot to check the compatibility of the surface with the product.

Treatment:
1. Sand old and previously treated surfaces with grit 180 sandpaper. Vacuum clean the surface thoroughly.
2. Thoroughly clean the surface with WOCA Intensive Wood Cleaner, mixed 1 part cleaner to 20 parts water. After cleaning, leave the work surface to dry for at least 8 hours at 20°C.
3. Mix the oil thoroughly.
4. Use a paintbrush to distribute an appropriate amount of oil in an even, covering coat. If possible, the reverse side of the work surface should also be given a coat of oil.
5. Wait approx. 30 minutes at 20°C, while the oil soaks into the wood. Apply more oil if dry areas appear.
6. Polish with the red or white WOCA hand scrubber along the direction of the wood grain. This will make the surface more durable.
7. Then wipe off all excess oil with a lint-free cotton cloth. No excess oil should remain on the surface.
8. Allow the surface to rest for an hour and repeat steps 3 to 7.
9. The surface should be treated two or three times before use. For the final treatment sand in wet oil with grain 280-400 sandpaper, before wiping off with a lint-free cotton cloth.
10. The oiled surface can be used after 24 hours at 20 degrees. During this period, the surface must not come into contact with water. The oil does not harden completely until after about a week. Therefore, treat with care during this period. Any spilled liquids should be wiped up immediately.

! Please note the worktop should be maintained at least once a year, or when necessary. For a superior result, use Worktop Oil or WOCA Maintenance Gel. For a more thorough restoration, follow the entire procedure.

Application temperature: +15-25°C and approx. 50% air humidity

Drying time: approx. 8-10 hours at 20°C. Light use after 24 hours at 20°C. Fully hard use after 7 days at 20°C.

Consumption: approx. 12-15 m²/L

Storage: +10-25°C. Keep out of reach of children. Do not expose to heat (e.g. sunlight). Store frost-free during winter and cool during summer. Shelf life 3 years.

Gallery